An annular disk of mass $M$,inner radius $a$ and outer radius $b$ is placed on a horizontal surface with coefficient of friction $\mu$,as shown in the figure. At some time,an impulse $J_0 \hat{x}$ is applied at a height $h$ above the center of the disk. If $h=h_m$ then the disk rolls without slipping along the $x$-axis. Which of the following statement$(s)$ is(are) correct?
$(A)$ For $\mu \neq 0$ and $a \rightarrow 0, h_m=b / 2$
$(B)$ For $\mu \neq 0$ and $a \rightarrow b, h_m=b$
$(C)$ For $h=h_m$,the initial angular velocity does not depend on the inner radius $a$.
$(D)$ For $\mu=0$ and $h=0$,the wheel always slides without rolling.

$A$ $2 \, kg$ steel rod of length $0.6 \, m$ is clamped on a table vertically at its lower end and is free to rotate in a vertical plane. The upper end is pushed so that the rod falls under gravity. Ignoring the friction due to clamping at its lower end,the speed of the free end of the rod when it passes through its lowest position is $\ldots \ldots \ldots \ldots \, ms^{-1}$. (Take $g = 10 \, ms^{-2}$)

$A$ thin ring of mass $2 \ kg$ and radius $1 \ m$ is rolling without slipping on a horizontal plane with velocity $1 \ m/s$. $A$ small ball of mass $1 \ kg$,moving with velocity $2 \ m/s$ in the opposite direction,hits the ring at a height of $1.8 \ m$ and goes vertically up with velocity $1 \ m/s$. Immediately after the collision:
$(A)$ the ring has pure rotation about its stationary $CM$.
$(B)$ the ring comes to a complete stop.
$(C)$ friction between the ring and the ground is to the left.
$(D)$ there is no friction between the ring and the ground.

$A$ uniform sphere of radius $R$ is placed on a rough horizontal surface and given a linear velocity $v_0$ and angular velocity $\omega_0$ as shown. The sphere comes to rest after moving some distance to the right. It follows that:

$A$ disc of circumference $s$ is at rest at a point $A$ on a horizontal surface when a constant horizontal force begins to act on its centre. Between $A$ and $B$ there is sufficient friction to prevent slipping,and the surface is smooth to the right of $B$. $AB = s$. The disc moves from $A$ to $B$ in time $T$. To the right of $B$,

Two discs $A$ and $B$ are mounted coaxially on a vertical axle. The discs have moments of inertia $I$ and $2I$ respectively about the common axis. Disc $A$ is imparted an initial angular velocity $2\omega$ using the entire potential energy of a spring compressed by a distance $x_1$. Disc $B$ is imparted an angular velocity $\omega$ by a spring having the same spring constant and compressed by a distance $x_2$. Both the discs rotate in the clockwise direction.
$1.$ The ratio of $x_1/x_2$ is
$(A)$ $2$ $(B)$ $1/2$ $(C)$ $\sqrt{2}$ $(D)$ $1/\sqrt{2}$
$2.$ When disc $B$ is brought in contact with disc $A$,they acquire a common angular velocity in time $t$. The average frictional torque on one disc by the other during this period is
$(A)$ $\frac{2I\omega}{3t}$ $(B)$ $\frac{9I\omega}{2t}$ $(C)$ $\frac{9I\omega}{4t}$ $(D)$ $\frac{3I\omega}{2t}$
$3.$ The loss of kinetic energy during the above process is
$(A)$ $\frac{I\omega^2}{2}$ $(B)$ $\frac{I\omega^2}{3}$ $(C)$ $\frac{I\omega^2}{4}$ $(D)$ $\frac{I\omega^2}{6}$